how to install sharkbite fittings on existing copper pipe

Just push the tube into the fitting until you reach the depth mark. Today Im going to show you how I used SharkBite fittings to save some money on a plumbing fix.

Sharkbite 3 4 In Push To Connect X 1 2 In Mip Brass Reducing Adapter Fitting U138lfa

Be sure the pipe is free of scratches or debris and cut the pipe as cleanly and squarely.

. Position the pipe side prong so its fully seated on the pipe. No soldering no clamps no glue. To get started identify the pipe material.

Cut the copper pipe such that the ends are clear and sharp. The SharkBite Universal brass push-to-connect fittings create a seamless and easy transition between. Click to see full answer.

Tighten the clamping ring on the male fitting. Be sure the pipe is free of scratches or debris and cut the pipe as cleanly and squarely as possiblemeasure mark the insertion depth. Squeeze the handle to compress the release collar which is what makes the fitting let go of the pipe.

To check if the installation of the pipe is accurate and proper you must verify and see if the depth marked is within 0005 inches of the release collar ending. SharkBite fittings come with a PEX stiffener pre-loaded into the fitting for PEX PE-RT and HDPE. Insert copper pipe in the Suitable SharkBite Fitting Slightly turning the line push the pipe in the fitting until it.

Pull the fitting to remove it from the pipe. The steps to use the universal tool are simple. Sharkbite Fittings Are Used For Different Types Of Repairs.

Cut pipe cleanly squarely. 3 insert the pipe into the sharkbite fitting. Place the fitting side above the barrel of the SharkBite fitting.

1 Use a tapered wrench to tighten the fitting onto the pipe. Installing a Tectite Sharkbite Slip Tee onto a copper water pipe lineNOTE De- burr and Clean the inside AND outside of pipe after cuttingTo Purchase. You should then mark each pipe joint on end to show where the SharkBite fitting will fit.

Connect the male fitting to the female fitting using the supplied hose clamps. Insert Copper Pipe In The Suitable Sharkbite Fitting. Once youve cut the pipe so that its square use the SharkBite Depth Deburr Gage to mark insert depth on your pipe.

You only need a. Once inserted you should push the pipe using slight twisting motions firmly into the SharkBite fitting until you hit the tube stop. Whether you need to repair a broken pipe or plumb a whole house SharkBite provides a push-to-connect solution and leak-free results.

Now to join the fittings the following steps are to be done. CONNECTING THE FITTINGS 1. Learn how to install SharkBite push-to-connect fittings fast with this helpful How-To Video.

How To Install SharkBite Brass Push-To-Connect FittingsIdentify the pipe material. Avoid jagged ends with burrs. Insert the pipe through the release collar so that it can easily grab the ring.

Push the fitting to the insertion mark you just made on the pipe. 2 Make sure the fitting is tightened until the threads are flush with the surface of the pipe. In this step you need to insert the pipe into the SharkBite fitting.

The PEX stiffener does not need to be removed for Copper or CPVC applications. Replacing copper pipes and fittings with SharkBite push fit connectors is super easy. Hold the pipe firmly and push it into the SharkBite fitting with a slight force until it hits the tube spot.

Now push the pipe with a slight twisting motion. SharkBite products work with your existing plumbing are easy to disassemble for changing and reusing fittings and can be rotated for installation in tight spaces. There is no need for special tools or clamps.

How To Install Sharkbite Push To Connect Fittings Youtube

Sharkbite 3 4 X 3 4 Inch Fnpt Threaded Adapter Push To Connect Brass Plumbing Fitting Pex Pipe Copper Cpvc Pe Rt Hdpe U766lfa Faucet Spouts And Kits Amazon Com